Best Sheetrock Wall Anchors
As an Amazon Associate we earn from qualifying purchases. Details
Sheetrock is a trademark that many people use for any drywall, and the anchor you pick for it decides whether a shelf, mirror or curtain rod stays on the wall. The person searching for the best sheetrock wall anchors, or the best anchor for drywall, wants one thing: an anchor that will carry what they are hanging without pulling out of a hollow wall. This page compares nine anchor products from their Amazon listings, quotes each listing’s load figure exactly as written, and shows where the listings disagree with themselves. Check the current price on Amazon; this page does not list prices.
Quick answer
For anything heavier than a picture frame, start with a toggle-type anchor. The TOGGLER SNAPTOGGLE listing states the highest figure of the nine, 265 lbs in 1/2 inch drywall, but it calls that an ultimate tensile strength, which is a breaking number and not a safe working load. For medium jobs such as a mirror or a small shelf, the E-Z Ancor Twist-N-Lock (75 lb on the listing) is the simplest to install because it screws in without a pre-drilled hole. For light picture hanging, the large plastic assortment kits are the usual choice, but the KURUI 270 and Kevinrooty 310 kits state no load at all. Whatever you buy, a stud is still stronger than any drywall anchor when the shelf bracket lines up with one.
Specs checked on 2026-10-17 from the Amazon listing of each product.
How we chose
Every product here is sold for hollow drywall, and its listing says so. We left out masonry-only anchors and wedge anchors. The comparison uses the load figure each listing writes, the drywall thickness it names, the pack contents and the install method. We did not run pull-out tests, and the listings do not say how their figures were measured. Where a listing gives no load, the table says so rather than guessing. The one worked example further down is our own arithmetic, and we mark it as ours.
Comparison at a glance
| Product | Type (from the listing) | Load figure the listing states | Drywall or wall named | Pack |
|---|---|---|---|---|
| TOGGLER SNAPTOGGLE, 1/4-20 | Snap-toggle anchor with bolt | 265 lbs in 1/2 in drywall (ultimate tensile strength) | Fits 3/8 to 3-5/8 in hollow materials | 20 (other packs offered) |
| E-Z Ancor Twist-N-Lock #8 x 1-1/4 in | Screw-in anchor, no pre-drill | 75 lb | 1/2 in or 5/8 in drywall | 50 (25, 100, 200 offered) |
| KURUI 140 pc self-drilling | Nylon and glass-fiber, screw-in | 75 lb (two bullets agree) | Drywall | 140 pieces (anchors plus screws) |
| CrimsonMark 120 pc #8 | Ribbed nylon, glass fiber, screw-in | 75 lb | Sheetrock and other wall surfaces | 120 pieces: 60 anchors, 60 screws |
| Hillman Borefast 1-1/2 in | Self-drilling anchor, pan head | 50 lb in drywall; 200 lb in wood or masonry | Drywall, wood, metal, brick, plaster, masonry, concrete | 75 |
| KURUI 116 pc metal self-drilling | Zinc alloy, screw-in | 50 pounds | Drywall | 116 pieces (50 also offered) |
| KURUI toggle bolt and wing nut kit | Butterfly toggle bolts | No figure stated | Hollow walls | 28 pieces (44 also offered) |
| KURUI 270 pc assortment | Ribbed plastic with wood screws | No figure stated | Drywall, concrete, brick, wood | 270 = 135 anchors + 135 screws |
| Kevinrooty 310 pc | Nylon 6/6 with zinc steel screws | No figure stated | Gypsum board, lightweight concrete, hollow brick | 310 pieces in 3 sizes |
The anchors
1. TOGGLER SNAPTOGGLE Drywall Anchors, 1/4-20 bolts, 20 pack: highest stated figure
Specs (listing, checked 2026-10-17): 1/4″-20 UNC zinc-plated snap-toggle anchors that fit 3/8 to 3-5/8 inch hollow materials, including gypsum board, drywall and concrete block. The anchor attaches to the wall before the bolt and fixture go on, so one person can install it and the fixture can be taken off and put back. The listing says it is made in the USA.
Conflicts to know about: The title says the anchor “holds 265 lbs on drywall”, while a bullet calls 265 lbs the ultimate tensile strength in 1/2 inch drywall and adds “Follow safe working load guidelines”. Those are not the same thing, so do not hang 265 lbs on it. The concrete block figure is 802 lbs in the title and 1,080 lbs in the bullet. The title says “with bolts”, while one bullet says 1/4″-20 bolts are sold separately, so check what is in the box before you start.
Best for: Heavier shelves and cabinets in hollow drywall where no stud lines up. Skip if: You want a quick screw-in anchor for a light frame; this one takes more steps.
View on Amazon (affiliate link)
2. E-Z Ancor Twist-N-Lock #8 x 1-1/4 in, 75 lb, 50 pack: best for medium loads
Specs (listing, checked 2026-10-17): A #8 x 1-1/4 inch anchor you screw directly into 1/2 inch or 5/8 inch drywall without pre-drilling. The listing says an audible click tells you it is set and that it sits flush against the wall. The title and a bullet both give 75 lb, with uses named as shelving, mirrors and picture frames, and the listing calls it “medium-duty”.
Conflicts to know about: None in the listing. The listing does not say whether 75 lb is per anchor, and it does not say how the figure was measured.
Best for: A mirror, a light shelf or a curtain rod where you want one tool and no drilling. Skip if: The wall is thinner than 1/2 inch, or you need a number for a heavy load.
View on Amazon (affiliate link)
3. KURUI 140 pc #8 self-drilling anchors, 75 lb: value kit with a stated figure
Specs (listing, checked 2026-10-17): Anchors made of nylon mixed with glass fiber, driven in with a screwdriver or screw gun and no pre-drilled hole. A bullet says the anchors hold objects “with maximum weight of 75lbs”, and another says they “can hold up to 75 pounds”; the title ends in “-75LB”. The 140 count is anchors plus screws (70 and 70 in the version we read), and the listing calls them “recommended for medium-duty applications”.
Best for: A household that wants one box for frames, towel bars and light shelves. Skip if: You want a named brand’s published rating; this listing gives no test method.
View on Amazon (affiliate link)
4. CrimsonMark 120 pc #8 self-drilling kit, 75 lb
Specs (listing, checked 2026-10-17): 60 ribbed nylon anchors, 60 galvanized #8 x 1-1/4 inch screws and a clear case. The listing says the ribs “hold 75lbs”, that the glass-fiber nylon will not split under torque, and that the anchors can be removed and reused. It names TVs among the uses, which the other kits do not.
Conflict to know about: The listing names “TV” as a use, but gives only a 75 lb figure and no rule about how to share a TV’s weight across anchors. We would not take that as a TV-mount rating; use the TV mount’s own instructions and a stud where you can.
Best for: Light to medium hanging with a case that keeps screws sorted. Skip if: You need more than about 60 anchors.
View on Amazon (affiliate link)
5. Hillman Borefast 1-1/2 in pan head, 75 pack: the figure that separates drywall from wood
Specs (listing, checked 2026-10-17): Self-drilling anchors with Phillips pan heads, sold in a 75 pack. The listing says they support “up to 50 pounds in drywall and 200 pounds in wood or masonry”, that they are removable and reusable, and that they work in drywall, wood, metal, brick, plaster, masonry and concrete.
Note: This is the only listing here that gives different figures for different wall materials. The 50 lb figure is the one for drywall. The listing does not name a drywall thickness.
Best for: A mixed job that crosses drywall, plaster and masonry. Skip if: Your main use is hollow drywall and you want a higher figure; the 75 lb anchors above state more.
View on Amazon (affiliate link)
6. KURUI 116 pc metal self-drilling anchors, 50 lb
Specs (listing, checked 2026-10-17): Zinc alloy anchors with galvanized steel screws, installed with a screwdriver or screw gun. The large threads “can hold up to 50 pounds”, and the listing names bathroom and kitchen accessories, shelving, light fixtures, mirrors, picture frames, curtain rods and small shelves. Pack counts of 116 and 50 are offered.
Conflict to know about: This metal kit states 50 lb, while the same brand’s plastic 140-piece kit states 75 lb. A metal anchor is not automatically the stronger one on these listings, and neither listing says how its figure was reached.
Best for: Shoppers who prefer a metal anchor for bathroom or kitchen accessories. Skip if: You want the higher 75 lb figure.
View on Amazon (affiliate link)
7. KURUI toggle bolt and wing nut kit, 28 pieces: for hollow walls, with a clear limit
Specs (listing, checked 2026-10-17): Steel toggle bolts with a galvanized coating and butterfly wing nuts that open behind a hollow wall: 12 of 1/8 inch, 6 of 3/16 inch and 4 of 1/4 inch bolts with their nuts, in a clear case. A 44-piece pack is also offered.
Listing limits: No load figure is given. The listing says holding performance depends on wall condition, wall thickness and proper installation, that it suits pictures, mirrors, curtain rods and light shelving, and that it is “not recommended for televisions, heavy mounts, or heavy ceiling installations”. It is the most cautious listing of the nine.
Best for: Light shelves and curtain rods where a bolt through the wall is wanted. Skip if: You need a stated rating, or the job is a TV or a heavy mount.
View on Amazon (affiliate link)
8. KURUI 270 pc drywall anchor and screw assortment: picture-hanging box with no load figure
Specs (listing, checked 2026-10-17): 135 ribbed anchors made of a nylon and PE compound, 135 galvanized Phillips wood screws and a clear organizer box. The listing gives five sizes, written as #6 1″, #7 1″, #6 1-1/5″, #8 1-3/5″ and #8 2-2/5″, and names drywall, concrete, brick and wood as surfaces.
Listing limits: The listing does not state a load rating. The sizes are written with fractions such as 1-1/5 and 2-2/5 inches, which are unusual for screws, so check the screw length against the item before you rely on it.
Best for: Frames, small decor and a toolbox drawer of mixed sizes. Skip if: You need to know what the anchor holds.
View on Amazon (affiliate link)
9. Kevinrooty 310 pc nylon anchor kit in three sizes
Specs (listing, checked 2026-10-17): Nylon 6/6 anchors in three sizes (15x33mm x 60, 13x42mm x 70 and 13x32mm x 25) with matching zinc steel screws (#8 x 1-1/4 inch x 60, #8 x 1-1/2 inch x 70 and #6 x 1-1/4 inch x 25). The listing says they screw in with no pre-drilled hole and suit gypsum board, lightweight concrete and hollow brick.
Listing limits: No load rating is given, so treat it as a light-duty kit.
Best for: Stocking up for many small hangings. Skip if: The load matters.
View on Amazon (affiliate link)
How to read an anchor’s load figure
A listing figure is one number with several missing details. None of the nine listings says whether its figure is per anchor or for a whole set. Only the TOGGLER (tensile strength in 1/2 inch drywall) hints at what kind of load was measured, and only it and the E-Z Ancor (1/2 or 5/8 inch drywall) name a wall thickness. The wording also differs: “holds”, “up to”, “maximum weight” and “ultimate tensile strength” are not the same promise.
Worked example (our arithmetic, a rule of thumb, not a standard): You want to hang a 24 lb mirror on two anchors. Split evenly, each anchor carries 12 lb, which is 16 percent of a 75 lb figure and 24 percent of a 50 lb figure. Now take a floating shelf loaded with 30 lb of books on four anchors: 7.5 lb each, about 10 percent of 75. Both jobs sit well inside the listed numbers. A 60 lb load on two of the 50 lb anchors would put 30 lb on each, 60 percent of the figure, and that is where we would move to a toggle-type anchor or a stud. The even split is an assumption; a shelf load pulls harder on the top anchors than the bottom ones, so real loads are not equal.
The listings themselves tell you what to do next. The KURUI toggle kit warns that holding performance depends on wall condition, wall thickness and proper installation. The TOGGLER listing says to follow safe working load guidelines. If the number is critical, read the manufacturer’s page or packaging for a working load.
Anchor types, in plain terms
- Screw-in (threaded) anchors: E-Z Ancor, KURUI 140 and 116, CrimsonMark, Hillman and Kevinrooty. Quick, one tool, no pre-drilled hole per the listings. Stated figures run from 50 to 75 lb.
- Toggle bolts and snap toggles: TOGGLER and the KURUI toggle kit. More steps, and the part that spreads behind the wall is bigger. The TOGGLER states the highest figure; the KURUI kit states none.
- Plain ribbed plastic anchors: The KURUI 270 box sits here. Fine for frames; check the packaging for a rating.
Mistakes to avoid
- Treating the biggest number as the working load. The TOGGLER’s 265 lbs is described as ultimate strength on the same page that says to follow safe working load guidelines.
- Ignoring wall thickness. E-Z Ancor names 1/2 inch and 5/8 inch drywall, and TOGGLER names a 3/8 to 3-5/8 inch range. Check what is behind your wall before choosing.
- Using a drywall anchor on plaster, tile or masonry without checking. Several listings name concrete or brick (KURUI 270, Kevinrooty, Hillman), but only Hillman names plaster and gives a separate figure for masonry. The others give no figure for those surfaces.
- Skipping the studs. A shelf bracket that lines up with a stud needs no drywall anchor on that screw. A stud finder helps; read the shelf’s own hardware notes.
- Hanging a TV on an assortment-kit anchor. The KURUI toggle listing says it is not recommended for televisions or heavy mounts. The TOGGLER and CrimsonMark listings name TVs among their uses, but none of the nine listings gives a TV rating.
Who should skip buying anchors
If the shelf or mirror you bought already includes anchors rated for its weight, use those and read its instructions. If you rent, ask the landlord before putting holes in the wall. If the wall is plaster, brick or tile, a drywall anchor is the wrong tool.
Related guides on this site
- floating shelves that can hold weight
- bathroom floating shelves with a towel bar
- decorative floating wall shelves for the living room
- wire shelf weight limits
Frequently asked questions
What is the best anchor for drywall?
It depends on the load. Among the nine listings here, TOGGLER SNAPTOGGLE states the highest figure (265 lbs ultimate strength in 1/2 inch drywall), E-Z Ancor, KURUI 140 and CrimsonMark state 75 lb, and Hillman and the KURUI metal kit state 50 lb. A stud is still stronger than any of them.
Are sheetrock anchors and drywall anchors the same thing?
Yes. Sheetrock is a trademark that many people use for drywall, and listings use both words for the same anchors. Several listings above say “sheetrock” in the title or text.
Can I use these anchors for a TV?
The listings do not give a TV rating. The KURUI toggle kit says it is not recommended for televisions or heavy mounts, the TOGGLER and CrimsonMark listings name TVs as a use without a TV-specific figure, so follow the TV mount’s instructions and use studs where you can.
Do I need to pre-drill for a drywall anchor?
The screw-in anchors (E-Z Ancor, KURUI 140 and 116, CrimsonMark, Hillman, Kevinrooty) say no pre-drilling is needed. The toggle types need a hole large enough for the toggle to pass through; read the instructions in the box.
Can drywall anchors be reused?
Two listings say so: Hillman says its anchors are removable and reusable, and CrimsonMark says its anchors can be removed and reused. The others do not say.
How many anchors do I need for a shelf?
Use the number the shelf’s hardware calls for, and add up the load you plan to put on it. Our worked example above shows how a listed figure divides across anchors, but the even split is only an assumption.
Conclusion
Choose a toggle-type anchor, with TOGGLER SNAPTOGGLE as the one that states the highest figure, when a shelf or cabinet will carry real weight. Choose E-Z Ancor or a 75 lb screw-in kit for mirrors, light shelves and rods. Keep the no-rating kits for pictures. And whichever you buy, find the studs first.
