pot-rack
As an Amazon Associate we earn from qualifying purchases. Details
The person typing pot rack wants to hang pots, pans and lids off the wall or from the ceiling so the cabinet space they had been using is free again. A pot rack is a rail or shelf with hooks, and the three numbers that decide whether it works are the mount type, the stated shelf weight capacity and the length of the rail. Pick the mount first, because it determines where the rack can go, and then check whether the listing states a load you can trust.
This guide compares five pot racks whose listings we opened on Amazon. Two are ceiling mounts and three are wall mounts.
Quick answer
- Wall rack: choose this if you have a solid wall above a counter and can drill into studs or use rated anchors. The three wall models here state shelf capacities of 50, 80 and 100 pounds.
- Ceiling rack: choose this only if you can reach a ceiling joist or a rated fixing point. The one ceiling model that states a shelf capacity lists 50 pounds, and no ceiling listing states a rating for its fixing.
- Before you buy: measure the wall or ceiling space, the depth you need for your largest pan, and the spacing of the studs or joists. Then compare the stated numbers with those measurements.
How we chose
We searched Amazon for pot racks and opened five product pages whose titles describe a pot or pan rack with hooks. Each page was checked against its ASIN in the address bar and its title. We skipped entries that were drawer organisers, utensil crocks or magnetic knife strips, because they do not hold cookware in the same way. We did not rank by price, rating or review count, and we did not record them.
For mounting guidance we opened two pages from the U.S. Consumer Product Safety Commission’s Anchor It! campaign: the CPSC news release of 29 July 2025 and the anchorit.gov resources page. These sources cover anchoring furniture to walls. They do not give load ratings for kitchen racks, so every load figure below comes from a listing, and the listing’s wording is quoted as the source.
Mounting first: wall, ceiling, or both
A wall rack transfers its weight to the wall through the screws or anchors in the mounting holes. A ceiling rack transfers it to the ceiling through hanging chains or rods and a fixing point overhead. Each has a different failure point, so the choice should start with what your house can support.
For wall racks, look for studs first. The KES listing describes two mounting holes 16 inches apart that extend downward, which the listing presents as a stud-mounting design. Measure the stud spacing in your own wall with a stud finder before you mark the holes, because the listing’s 16-inch hole spacing only helps if a stud falls where the holes do. If the wall is plaster, masonry or thin drywall with no stud at the right spot, use anchors rated for the weight, and read the anchor packaging rather than a generic figure. The CPSC release and the anchorit.gov materials both emphasize anchoring furniture and fixtures to the wall, and the same principle applies to a loaded rack.
For ceiling racks, the listing’s shelf capacity is only one part of the load. The rack hangs from its mounting point, so the ceiling fixing and the joist behind it carry the weight. Neither ceiling listing we read states a rating for the ceiling fixing itself, so treat the 50-pound shelf figure as the rack’s stated limit and do not assume the ceiling can take it without checking the structure.
The five pot racks
1. KES 30-Inch Kitchen Pot Rack, matte black wall rack (B07MLF234K)
This is a wall-mount rack with a grid shelf and 12 movable S-shaped hooks. The listing gives its size as 9.8 inches deep, 29.9 inches wide and 20.5 inches high, with an item weight of 7 pounds. It is metal with a powder-coated black finish.
- Mounting type: Wall Mount
- Shelf weight capacity (field): 50 pounds
- Dimensions: 9.8 in D x 29.9 in W x 20.5 in H
- Listing bullet: “Max. Load: 100 lbs, screw-mounted on solid concrete wall”
The listing contains a conflict. Its shelf capacity field says 50 pounds, while a bullet says 100 pounds on a solid concrete wall. Those two figures describe different conditions, and the listing does not reconcile them. Use the lower figure unless you are mounting into concrete and have confirmed the anchor rating. The grid shelf and detachable hooks make this rack suitable for stacking lids and pans on the shelf and hanging utensils below.
2. CHOEZON Hanging Pot Rack, ceiling mount with 12 S hooks (B0DMP5SG8H)
This is a ceiling-mount rack with an upper metal mesh shelf that the listing gives as 31.5 inches long by 15.7 inches wide, with 12 S hooks beneath. The listing states dimensions of 15.7 inches deep, 31.5 inches wide and 13 inches high, a weight of 9.02 pounds, and a shelf weight capacity of 50 pounds. Its materials are engineered wood and metal, in a rustic brown and black finish.
- Mounting type: Ceiling Mount
- Shelf weight capacity: 50 pounds
- Listing bullet: the double chains are described as supporting up to 50 pounds
- Dimensions: 15.7 in D x 31.5 in W x 13 in H
This rack is a good fit when a ceiling joist sits where you want the rack, and when you can reach the ceiling fixing point. Its 31.5-inch width is wide enough for a row of large pans if the ceiling space is clear. Because the listing describes a ceiling mount but does not state a rating for the ceiling fixing, check the joist and the fixing before you load it.
3. PXRACK 19 to 30 Inch Expandable Pot Rack (B0CB68KCBC)
This wall-mount rack is titled as expandable from 19 to 30 inches and as a two-tier rack with 10 hooks and five pot lid holders. The listing gives a shelf weight capacity of 100 pounds and a material of carbon steel with a powder-coated black finish. The listing describes two removable trays that let you change the height for different cookware.
- Mounting type: Wall Mount
- Shelf weight capacity: 100 pounds
- Length: expands from 19 inches to 30 inches
- Material: carbon steel, powder coated
The 100-pound figure is the highest shelf capacity among the wall racks here, and the listing does not say what wall or anchor it assumes. Treat that number as the rack’s limit, not as the limit of the wall. The expandable length suits a kitchen with a short run of wall. The overall item dimensions were not captured on the fields we read, so measure the rack after delivery and before you commit to a mounting plan.
4. Boshangjia 24 Inch Pipe Pot Rack (B0FR26PCM5)
This is a wall-mount iron pipe rail, described as 1-inch diameter pipe with a matte coating against rust. The listing gives a shelf weight capacity of 80 pounds, dimensions of 24 inches deep, 2.3 inches wide and 3.6 inches high, and an item weight of 1.76 pounds. The rail is detachable and carries S hooks.
- Mounting type: Wall Mount
- Shelf weight capacity: 80 pounds
- Dimensions: 24 in D x 2.3 in W x 3.6 in H
- Hooks: the title says 6 S hooks; a bullet says 10 S hooks can be moved along the rail
The hook count conflicts between the title and a bullet, so count the hooks in the box when it arrives. The rail’s 24-inch depth is a practical detail: it sets how far the pans stand out from the wall. A rail this light is easy to lift into place, but its stated 80-pound capacity still depends on the fixings you use.
5. Ceiling-mount pot rack, 31.7 inch model with 16 S hooks (B0DS24STY8)
This ceiling rack is titled as 31.7 inches wide with a sturdy metal frame and 16 detachable S hooks. The listing gives product dimensions of 13 by 31.7 by 2.4 inches and an item weight of 5.88 pounds. Its bullets describe black metal with rustic brown engineered wood panels and curved sides that the listing says add storage.
- Mounting type: ceiling, per the title
- Weight capacity: not stated in the fields we read
- Dimensions: 13 x 31.7 x 2.4 in (as listed)
We could not capture the brand or a mount-type field from this page, and the listing does not state a load. Do not assume a capacity. If you choose this rack, ask the seller or read the full specification table before you install it, and treat the ceiling fixing as the limiting factor until the listing states otherwise.
Worked example: how much room the rack needs
This is a planning estimate, not a product specification. Suppose your largest pan is 13 inches across the handle and you want it to hang clear of the wall. If the rack is 9.8 inches deep, as the KES listing states, the pan’s handle and hooks need at least that much forward clearance from the wall. Check it this way: 9.8 inches of rack depth plus 13 inches of pan diameter, compared with the distance from the wall to the nearest obstacle, such as a range hood or a cabinet door. If the rack is 24 inches deep, as the Boshangjia listing states, the same check uses 24 inches, which means the rail stands well out from the wall and needs a clear run in front of it.
For load, a simple planning check uses the stated shelf figure minus the weight of what you plan to hang. A 50-pound shelf with a 12-pound skillet set on it leaves 50 minus 12, or 38 pounds of margin in the stated figure. That margin does not account for the wall, the screws or the way the load is distributed, so it is only a starting point.
Where the listings conflict
- KES B07MLF234K: shelf capacity 50 pounds in one field and 100 pounds on a concrete wall in a bullet.
- Boshangjia B0FR26PCM5: 6 S hooks in the title and 10 S hooks in a bullet.
- Ceiling model B0DS24STY8: brand and mount-type fields not captured; title says ceiling mount; no load stated.
When a listing conflicts with itself, the safe reading is the lower figure and the more conservative detail. Confirm the detail in the product’s packaging or manual before you drill.
What we could not verify
The listings and the two CPSC and anchorit.gov pages we opened do not establish the following. The rated load of any anchor or screw that comes with these racks. The load each ceiling fixing point can take in a particular house. Whether the 100-pound figure on the KES page applies to a drywall wall. The overall dimensions of the PXRACK model, which were not captured. How the racks perform with heavy cast iron, which the listings do not address. The sources named above do not give a rating for the fixings that ship with each rack.
Common mistakes
Mounting into drywall without a stud
Drywall alone does not carry a loaded rack. If the mounting holes do not hit a stud, use an anchor rated for the rack’s load and read its packaging for the wall type it is designed for. Do not use the rack’s shelf figure as the anchor’s rating.
Measuring the wall but not the pan
A 9.8-inch or 24-inch deep rack looks small on a listing. Add the depth of the pans you actually own, including handles, before you choose. A shallow rail can still hit a range hood if the hood projects forward.
Ignoring the ceiling joist
A ceiling rack is only as strong as the structure above it. Locate the joist and confirm the fixing before you hang the rack.
Buying the wrong product type
A drawer organiser or a utensil crock is not a pot rack. If you need drawer dividers for cutlery, our separate guide on kitchen organisers for spices covers a different problem.
Pot rack or cabinet storage?
A pot rack frees cabinet space by moving heavy cookware to the wall or ceiling, but it also puts pans in view and in the way of the cook. If the cookware is mainly used for storage and you want it out of sight, a cabinet organiser may be the better choice. If the cookware is used daily and you want it within reach, a rack is worth the effort of a secure mount. For shelves that might also carry dishes, read about wall shelves and their stated limits before you combine a shelf with a rack on the same wall.
Frequently asked questions
What is the difference between a wall pot rack and a ceiling pot rack?
A wall rack transfers its weight through the wall fixings, while a ceiling rack hangs from a fixing in the ceiling. The wall rack needs studs or rated anchors. The ceiling rack needs a joist or a rated overhead fixing point. Choose by where your structure can carry the load.
How much weight can a pot rack hold?
The listings we read state shelf weight capacities of 50, 80 and 100 pounds for the racks that give a figure. The KES listing states both 50 pounds and 100 pounds on a concrete wall, so read the conditions carefully. The stated figure is the rack’s limit, and the wall or ceiling fixing may be lower.
Can I mount a pot rack into drywall?
Mount it into a stud where you can. If no stud falls at the right spot, use anchors rated for the load and the wall type. The CPSC and anchorit.gov materials emphasize anchoring furniture to the wall, and the same care applies here.
Which length should I choose?
Choose the length that fits the open wall or ceiling run and leaves room for your largest pan. The PXRACK model expands from 19 to 30 inches, and the KES model is 29.9 inches wide. Measure the run before you order.
How many hooks do I need?
Count the cookware you hang regularly, then add a few hooks for lids and utensils. Note that some listings conflict on hook count, so check the box contents before you assume a number.
Bottom line
Choose the mount your structure can carry, then pick the rack whose stated capacity and length match your wall. For a wall rack with the clearest stated capacity, compare the 100-pound PXRACK listing with the 80-pound Boshangjia listing and confirm the fixings before you drill. For a ceiling rack, confirm the joist before you buy.
Sources
- U.S. Consumer Product Safety Commission, “CPSC Anchor It! Campaign Marks 10 Years: Fewer Furniture Tip-Overs Lead to Safer American Households,” news release dated 29 July 2025, https://www.cpsc.gov/Newsroom/News-Releases/2025/CPSC-AnchorIt-Campaign-Marks-10-Years-Fewer-Furniture-Tip-Overs-Lead-to-Safer-American-Households (opened 2026-10-29).
- Anchor It!, “Resources,” https://www.anchorit.gov/resources/ (opened 2026-10-29).
- Amazon.com listing pages, read 2026-10-29: B07MLF234K, B0DS24STY8, B0CB68KCBC, B0FR26PCM5, B0DMP5SG8H.
Disclosure: links on this page are affiliate links. Prices, ratings and availability change, so check each listing before you buy. Specifications come from the listings and sources named above.
